There are many things to consider that greatly affect the price such as the brand, efficiency, model and access. There is also a big cost difference between replacing an existing system and installing a new system. Installing air conditioning can cost from about $7,000 to well over $20,000 depending on many factors. The average cost for a good system is about $12,000. Time Plumbing, Heating & Electric offers financing Programs W.A.C. that can help with the expense.

There are many things to consider that can greatly affect the price. Installing a new air conditioning system will take from about 16 to over 60 hours to install. So the labor alone would cost about $3200 to $12,000 with the average being about $5,000. We offer financing Programs W.A.C. that can help with the expense.

There are many things to consider that greatly affect the price such as the brand, efficiency, model and access. There is also a big cost difference between replacing an existing system and installing a new system. Installing air conditioning can cost from about $7,000 to well over $20,000 depending on many factors. The average cost for a good system is about $12,000. We offer financing Programs W.A.C. that can help with the expense.

There are many things to consider that greatly affect the price such as the brand, efficiency, model, access, and if the electrical, the line set and the coil can be reused. The cost to replace a central AC unit in Denver is between about $5,000 to over $20,000 with the average being around $10,000. We offer financing Programs W.A.C. that can help with the expense.

There are many things to consider that greatly affect the price such as the brand, efficiency, model and access. There is also a big cost difference between replacing an existing system and installing a new system. Installing air conditioning can cost from about $7,000 to well over $20,000 depending on many factors. The average cost for a good system is about $12,000. We offer financing Programs W.A.C. that can help with the expense.

The condenser is the heart of the system and is the most expensive part of the system to replace. There are many factors that affect the price to replace the condenser. Older systems with R-22 freon will in most cases require a conversion to one of the newer freon’s like 410-A freon as R-22 freon is being phased out. A condenser replacement can cost from about $5,000 to over $15,000 depending on many things with the average condenser replacement cost being about $7,500. We offer financing Programs W.A.C. that can help with the expense.

Look on Craig’s list, Good luck. Buying cheap equipment can become very expensive very quickly. Buyer Beware.

It depends on many things, how old is the unit? Is it a good quality one or a builder’s grade one? Have you had many problems in the past? How long do you plan on staying there? How much is it to repair? Can you afford a new unit? We are happy to give you a second opinion or diagnose what is going on and give you options.

This could go either way. If the unit is 7 years or older it is recommended to replace the condenser unit. You can replace the compressor only for less than the whole unite but if it is over 7 years old it can have many other issues that can cost as much or more than a new condenser to repair.

Yes you can replace it as long as it is using one of the newer freon’s. If your system uses R-22 freon than the condenser and inside coil will need to be replaced. The line set will need to be either flushed or replaced.

It depends on a lot of things such as how often has it been serviced, is it a builders grade or a high end unit and many other factors. The average life of a compressor or condensing unit is about 11 to 15 years. Condensers or compressors can fail in as soon as 3 years and in some cases last over 30 years. Once something starts acting up on an older unit it can be a chain reaction of problems that can get very expensive, if you have an older unit it may be well worth replacing it. Also older units cost a lot more to operate than the newer units, this helps offset the cost of a new unit.

There are a lot of different factors involved that can affect the time needed to replace the outside condensing ac unit. The time could be from about 5 hours to over 20. The average time is about 8 hours.

HVAC companies slowdown between January to May and also September and October. Because these are slower times many companies will offer some bigger discounts than normally to help fill in the gap.

It depends on a lot of things such as how often has it been serviced, is it a builders grade or a high end unit and many other factors. The average life of a compressor or condensing unit is about 11 to 15 years. Condensers or compressors can fail in as soon as 3 years and in some cases last over 30 years. Once something starts acting up on an older unit it can be a chain reaction of problems that can get very expensive, if you have an older unit it may be well worth replacing it. Also older units cost a lot more to operate than the newer units, this helps offset the cost of a new unit.

There are so many variables involved that to get an accurate price a property evaluation is needed to look at the different options and what the least destructive and most cost effective way to meet your needs for cooling. These systems can run from about $12,000 to over $30,000 depending on many factors.

There are many reasons that can cause this. If you see icing around the inside coil or the outside condensing unit than it is either low on freon or there is a flow problem from a dirty filter. There can also be many other things that can cause this and would require a technician to check the safeties and other things that can cause this issue. It this happens it is best to shut off the system to prevent extensive damage from happening.

There are many reasons that can cause this. If you see icing around the inside coil or the outside condensing unit than it is either low on freon or there is a flow problem from a dirty filter. It this happens it is best to shut off the system to prevent extensive damage from happening. There can also be many other things that can cause this and would require a technician to check the safeties and other things that can cause this issue.

There are so many things that can cause this like simply changing the furnace air filter all the way up to needing to replace the system. The average cost to repair an air conditioner or AC system that is not working is about $800.

This could go either way. If the unit is 7 years or older it is recommended to replace the condenser unit. You can replace the compressor only for less than the whole unite but if it is over 7 years old it can have many other issues that can cost as much or more than a new condenser to repair.

In some cause yes insurance will cover the cost, but it is rear. I have seen a house get struck by lightning and get a new unit from insurance. I have also seen major hail damage to the unit that was covered by insurance. Other that it is usually not covered by insurance.

The condenser is the heart of the system and is the most expensive part of the system to replace. There are many factors that affect the price to replace the condenser. Older systems with R-22 freon will in most cases require a conversion to one of the newer freon’s like 410-A freon as R-22 freon is being phased out. A condenser replacement can cost from about $5,000 to over $15,000 depending on many things with the average condenser replacement cost being about $7,500. We offer financing Programs W.A.C. that can help with the expense.

There are many things to consider that greatly affect the price such as the brand, efficiency, model and access. There is also a big cost difference between replacing an existing system and installing a new system. Installing air conditioning can cost from about $7,000 to well over $20,000 depending on many factors. The average cost for a good system is about $12,000. We offer financing Programs W.A.C. that can help with the expense.

Look on Craig’s list, Good luck. Buying cheap equipment can become very expensive very quickly.

Changing either the furnace filter or the battery in the thermostat. Be sure to service your system yearly just like changing the oil in your car it is important for extending the life of the equipment.

It depends on a lot of things such as how often has it been serviced, is it a builders grade or a high end unit and many other factors. The average life of a compressor or condensing unit is about 11 to 15 years. Condensers or compressors can fail in as soon as 3 years and in some cases last over 30 years. Once something starts acting up on an older unit it can be a chain reaction of problems that can get very expensive, if you have an older unit it may be well worth replacing it. Also older units cost a lot more to operate than the newer units, this helps offset the cost of a new unit.

Changing either the furnace filter or the battery in the thermostat. Be sure to service your system yearly just like changing the oil in your car it is important for extending the life of the equipment. There can be so many things that can fail at any time such as, the capacitor, dirty filter, dirty contactor, freon leaks, safety that has tripped or the compressor. We can accurately diagnose any problems, give you options and fix it right.

Changing either the furnace filter or the battery in the thermostat are common problems. Be sure to service your system yearly just like changing the oil in your car it is important for extending the life of the equipment. There can be so many things that can fail at any time such as, the capacitor, dirty filter, dirty contactor, freon leaks, safety that has tripped or the compressor. We can accurately diagnose any problems, give you options and fix it right.

There are many different ways to service the air conditioner or AC unit. There is a safety service and inspection that makes sure the system is operating safely. There is a safety service, inspection and calibration, same as above but also calibrating the unit to operate at the manufacture’s specifications. There is a lean and service that includes all above along with cleaning the accessible areas of the furnace. These services can range from $29 to over $300. Most commonly these range from $69 to $140

Yes, Yes, Yes. For the same reason you change the oil in your car, to prevent engine failure or major expenses. Your air conditioning system can become dirty causing things to operate hot and have to work a lot harder than normal. This can cause expensive things to fail prematurely. For every $1 spent on service is saving you at least 10 times that for repairs that will be needed from neglecting the system.

It should be serviced once a year or at least every 2 years for the same reason you change the oil in your car, to prevent major failures and expenses. Your air conditioning system can become dirty causing things to operate hot and have to work a lot harder than normal. This can cause expensive things to fail prematurely. For every $1 spent on service is saving you at least 10 times that for repairs that will be needed from neglecting the system.

There are many things to consider that greatly affect the price such as the brand, efficiency, model, access, and if the electrical, the line set and the coil can be reused. The cost to replace a central AC unit in Denver is between about $5,000 to over $20,000 with the average being around $10,000. We offer financing Programs W.A.C. that can help with the expense.

There are many things to consider that greatly affect the price such as the brand, efficiency, model and access. There is also a big cost difference between replacing an existing system and installing a new system. Installing air conditioning can cost from about $7,000 to well over $20,000 depending on many factors. The average cost for a good system is about $12,000. We offer financing Programs W.A.C. that can help with the expense.

It depends on a lot of things such as how often has it been serviced, is it a builders grade or a high end unit and many other factors. The average life of a compressor or condensing unit is about 11 to 15 years. Condensers or compressors can fail in as soon as 3 years and in some cases last over 30 years. Once something starts acting up on an older unit it can be a chain reaction of problems that can get very expensive, if you have an older unit it may be well worth replacing it. Also older units cost a lot more to operate than the newer units, this helps offset the cost of a new unit.

Yes you can leave your AC on all day. As long as it has been serviced, they are designed to run all day if needed. The system should cycle on and off as needed depending on the thermostat setting.

Yes you can leave your AC on all day. As long as it has been serviced, they are designed to run all day if needed. The system should cycle on and off as needed depending on the thermostat setting.

It depends, it is better and less expensive to operate on auto. It is also better to leave it on auto if the system is cooling the areas that are important to you. If you are not getting good cooling on the upper floor or in certain areas it is better to leave the fan in the on position. This will circulate the upper heated air better and cool areas that are not getting enough cooling.

Most people keep the AC at about 78 to 80 degrees, when leaving during the day you should raise the temperature about 5 degrees. If you go to high than it can be difficult for the system to bring the temperature back down,Is it cheaper to turn AC off at night? It may save a little but it will need to recover in the morning. It is recommended to set it up 2 to 3 degrees at night.

As long as needed to satisfy your cooling needs. Some systems are under sized and need to run all day to try to keep up, some are sized correctly and some are oversized. No matter what size your system is it all depends on your cooling needs and your budget. The lower you set it the more it will cost you to operate it.

This varies with each person. Find a temperature that is comfortable and that works with your budget. The cooler you have it the more it will cost to operate. Most commonly it is set at 78 to 80 degrees.

It depends, it is better and less expensive to operate on auto. It is also better to leave it on auto if the system is cooling the areas that are important to you. If you are not getting good cooling on the upper floor or in certain areas it is better to leave the fan in the on position. This will circulate the upper heated air better and cool areas that are not getting enough cooling.

There are a lot of variables that go into the pricing. Contractors are required to bring certain things up to code if they are not. Like an approved gas shut off and flex connector along with an expansion tank or pressure relief device. There are also many options with water heaters such as the efficiency of the heater and quality, just like buying a car. The fuel source, natural gas, propane and electric. The type of heater, on demand, instantaneous and some connected to a boiler system. Tank type ones installed can cost from about $1500 to over $10,000 depending on many factors. The average tank type replacement is about $3,430. The average on demand system or instantaneous system is about $6,710 and the average boiler type is about $5,800. Many companies offer easy financing to help with this unexpected expense. It is best to find a reputable company that has been around for a long time to get an accurate price.

There are many factors to be considered when replacing a water heater such as the type of water heater, If things need to be done to bring up to code, If you are replacing like for like increasing the size or changing the type or style of water heater. Keep in mind that if you supply your own water heater to be installed the company installing your water heater will not warranty it if something happens to go wrong. This can become extremely expensive if you were to get a lemon. The labor to install a basic tank type water could be anywhere from $850 to over $3,000. The labor to install an instantaneous or on demand water heater would start about $2,500 and can go as high as $7,000. It is best to find a reputable company that has been around for a long time to get an accurate price.

FAQs can be added to any page on your site or to your Wix mobile app, giving access to members on the go.This is difficult to answer but here you go. You are required to pull a permit anytime the domestic water system is opened up which includes a water heater. Every contractor is supposed to pull a permit to change a washer in a faucet, work on a fill valve in a toilet or change a faucet. There is not any contractors that pull permits to work on these. As for water heaters, yes you are supposed to pull a permit to install a water heater. Once a permit is pulled you are required to bring everything in the area up to current code, this is not an option. If the inspector requires fresh air to the room, to have a one hour fire rated door or drywall, to install fresh air or relief air vents, install a floor drain if one does not exist or many other things that can be very expensive. It is not an option you will be required to make these changes. In doing this for over 40 years I have seen people have over $10,000 in extras needed to bring the area up to current code. I have seen people that can barely afford the water heater have to do so many extras that they almost lose their home over it. Pulling a permit makes a lot of money for companies, so just be careful. If you use a contractor that does not pull a permit use a company that has been around at least 10 years and has good ratings.

The correct answer is that Lowes and or Home Depot do not install water heaters using their own people. They sub it out to contractors on their vender list. Most if not all of these companies pay their employees by commission, this means the more they can sell you the more the technician will make. These companies also pay a percentage of the job back to Lowes or Home Depot. These jobs can start off sounding very good only to end up costing a lot more than expected. Many times you can do a lot better shopping from a long established company that has good reviews and is a member of the BBB.

Different types of water heaters require different types of service. A tank type water heater should be serviced every 3 to 5 years, the average cost is about $120. Tankless or on demand types are required to be serviced and acid flushed every year or you will lose the factory warranty, the average cost to service and acid flush one of these $380.

(This is copied from above, Let me know if it needs Changed) There are a lot of variables that go into the pricing. Contractors are required to bring certain things up to code if they are not. Like an approved gas shut off and flex connector along with an expansion tank or pressure relief device. There are also many options with water heaters such as the efficiency of the heater and quality, just like buying a car. The fuel source, natural gas, propane and electric. The type of heater, on demand, instantaneous and some connected to a boiler system. Tank type ones installed can cost from about $1500 to over $10,000 depending on many factors. The average tank type replacement is about $3,430. The average on demand system or instantaneous system is about $6,710 and the average boiler type is about $5,800. Many companies offer easy financing to help with this unexpected expense. It is best to find a reputable company that has been around for a long time to get an accurate price.

The average cost to flush out a tank type water heater is about $120, Some companies offer specials as low as $39. Just be cautious of some of the companies with the very low pricing as many times they will try to sell things that may not be needed. For the tankless and on demand type water heaters they are required to be serviced and acid flushed every year or you may loose the factory warranty, The average cost to do this is about $380

There are many different types of water heaters with different types of problems. Tank type water heaters have filters that should be inspected and cleaned every couple of years, if not the burner area can over heat and cause the heat safety to burn out. Otherwise very few problems for the life of the water heater. On Demand and tankless type require a full service and acid flush every year or it may void the warranty. These have a lot of moving parts, safeties, and 1 to 3 computer boards that can at anytime act up and cause some very expensive problems.

There are many things that can cause a water heater to stop working. Many times it is one of the safeties that has tripped out due to some type of safety issue, or it could just be a part that has failed. It is recommended to get a qualified professional out to diagnose what is wrong and to see if there is an underlying safety issue that caused the problem to begin with.

The average life of a water heater is about 10.2 years. There are many different that have an average of less than 7 years. The longest we see are the Bradford White tank type with an average life of 16.8 years

Many things can help to stretch what you have. Install water conserving shower heads. Plan out when you are using things that use hot water, try to avoid washing dishes or clothes one hour before taking a shower or filling the bathtub. Try to shorten your shower or if you turn it off while soaping up and washing you will have a lot more water at the end. You can also turn up the temperature at the water heater, this needs to be done cautiously because if you do not have scald guard faucets some could possibly get scalded or burnt. This is not recommended with elderly people as they cannot sense temperature or react as fast. There are other options like installing a bigger system that can produce a lot more hot water. Our favorite after installing water heaters for over 40 years is the Bradford White 55 gallon 80,000 btu high recovery water heater. They produce a lot of hot water, they are much less costly to install than the instantaneous or on demand water heater, they do not require yearly maintenance, the average life is 16.8 years, and they rarely have problems before the end of its life.

This is a tough one to answer. Many plumbers that are on commission will only give you the most expensive solution because they make more money. Find one with some good reviews and make sure they belong to the Denver BBB and some of the other reputable referring companies Like Team Dave Logan, The Trouble Shooter, Five Star rated. We Are A+ Rated with the BBB and a leading member of all of the certified referral companies. Even with good companies you still need to use your best judgment on making your decision. Trust will come over time and until that time always be a little cautious.

There are many factors involved that can determine the price. Here are some of the things that effect the price. A hot water or steam boiler, the efficiencies range from 82% to 98%, Different features such as a constant speed or variable speed blower, a 2 stage system, there are builders grade models to high quality models, access and location such as a tight closet or closet and if things are needed to bring up to code or make safe. All of these will affect the price to replace a furnace. Replacing a furnace can range from about $4,000 to over $16,000. Pricing is dependent a lot on the company you are working with and what features are important to you along with your budget. Financing is usually available that can help spread out the cost over time.

The most common issues we encounter are the high limit switch tripping out due to not changing the filter often enough. Other problems can be the igniter failing, the flame sensor failing or needing cleaned, the draft inducer failing or the main control board failing.

I would say it would be the heat exchanger would be the most expensive repair on a boiler. These are replicable in most cases but can cost almost as much as a new boiler. If this fails, it is recommended to replace the furnace. The main control gas valve, control board or the circulating pump these can cost from $1,200 to about $2,800. By having a professional company do a yearly service and maintenance will increase the life of the furnace by many years and save on a lot of repairs.

It depends on a lot of factors such as, the age of the furnace, what the problem is and cost to repair it, is your boiler heating all of the areas to your satisfaction, what your budget is and whether you are planning to move soon or if you are planning to be there for a long time. All of these should be considered before making your decision.

The length of servicing your boiler depends a lot on the type of system, Steam boilers need to be serviced a lot more than a hot water system. A steam boiler should have the low water cut off flushed every month or two, this can be done by the home owner if shown how to by a reputable company like us. Hot water systems should be serviced at least yearly. It is good to have a professional service the boiler yearly.

The average life expectancy should be about 12 years to 25 years. There are a lot of factors that have an effect on the life of a furnace like the brand and model of the furnace, how often is has been serviced and the environment it is in. What does a furnace service include? There are a lot of things that should be done while servicing a Boiler, 1. Check and adjust the fill valve. 2. Clean and oil the circulating pump. 3. Bleed air from the system and test the air valve. 4. Clean the burners if needed. 5. Adjust and calibrate the burners and gas control valve. 6. Visually inspect the heat exchanger for cracks leaks or sooting. 7. Preform a C.O. test to see if Carbon Monoxide is leaking. 8. Test the safeties to see that they are working. 9. Check the gas control valve and fittings to see if there are any gas leaks. 10. Check the electrical connections to make sure they are tight. 11. Check the amp draw on the pump motor. 12. Check the resistance on the igniter. 13. Clean and inspect the flame sensor. 14. Oil any points on the pump when required. 15. Inspect the flue piping to make sure it is safe. 16. Clean and inspect the draft inducer. 17. Inspect for any rust areas that may be a problem.

Yes you can do a basic service by flushing the low water cut off or oiling the pump, it is strongly recommended that a professional should do a yearly service to make sure all things are operating safely.

By not servicing you boiler can cause some serious and expensive problems to occur. The biggest problem is when the low water cut off is not serviced, it can cause the boiler to overheat and can cause extensive damage and system failure. It can crack the heat exchanger creating a serious health safety issue, it will also add extra stress on many parts that can pre-maturely fail causing a dangerous and expensive situation with the boiler system.

The average life expectancy should be about 12 years to 25 years. There are a lot of factors that have an effect on the life of a furnace, like the brand and model of the furnace, how often is has been serviced and the environment it is in.

A service and clean should take anywhere from about 30 minutes to 90 minutes.

Yes, by preforming a tune up the system will operate better with less break downs, the air will flow through the furnace making it more energy efficient, by calibrating the gas valve to the manufacturer’s specifications it will operate more efficiently. By servicing a furnace you should save from 5% to 15% of the operating costs and lengthen the life of the parts.

How much does it cost to replace a Boiler in Denver?

There are many reasons that can cause a boiler or furnace to stop working. You should check the thermostat to start, the batteries in some thermostats can go dead and need replacement. There are many other safeties in a system that will not let it turn on if something is not right or you may have a component that has failed. Anything outside of the batteries you should have a professional out to diagnose what is going on and give you options to repair it.

There are many reasons that can cause a furnace to stop working. You should check the thermostat to start, the batteries in some thermostats can go dead and need replacement. There are many other safeties in a boiler that will not let it turn on if something is not right or you may have a component that has failed. Anything outside of the batteries you should have a professional out to diagnose what is going on and give you options to repair it.

If your Boiler system is older than 30 years and selling your home it can add the full cost of the new furnace back into the value of the home. A new system can be as much as 25% more efficient so even if you are not selling your home you will be saving a lot on your energy bills.

There are many factors involved that can determine the price. Here are some of the things that effect the price. Dealing with an existing AC system will add to the price, the efficiencies range from 82% to 98%, Different features such as a constant speed or variable speed blower, a 2 stage system, there are builders grade models to high quality models, access and location such as a tight closet or closet and if things are needed to bring up to code or make safe. All of these will affect the price to replace a furnace. Replacing a furnace can range from about $4,000 to over $16,000. Pricing is dependent a lot on the company you are working with and what features are important to you along with your budget. Financing is usually available that can help spread out the cost over time.

The most common issues we encounter are the high limit switch tripping out due to not changing the filter often enough. Other problems can be the igniter failing, the flame sensor failing or needing cleaned, the draft inducer failing or the main control board failing.

I would say it would be the heat exchanger would be the most expensive repair on a furnace. These are replicable in most cases but can cost almost as much as a new furnace. If this fails, it is recommended to replace the furnace. The second most costly would be a variable speed blower motor, these can cost from $1,200 to about $2,800. By having a professional company do a yearly service and maintenance will increase the life of the furnace by many years and save on a lot of repairs.

It depends on a lot of factors such as, the age of the furnace, what the problem is and cost to repair it, is your furnace heating all of the areas to your satisfaction, what your budget is and whether you are planning to move soon or if you are planning to be there for a long time. All of these should be considered before making your decision.

The length of servicing your furnace depends a lot on the type of filter you are using. The pleated filters that look like cloth filter better but get stopped up quickly and may need changed every 3 months. The older style that look like angel hair and you can see through them still filter but only need changed every year or two, these are also easier on the operation of the furnace. Furnaces should be serviced at least yearly. It is good to have a professional service the furnace yearly.

The average life expectancy should be about 12 years to 25 years. There are a lot of factors that have an effect on the life of a furnace like the brand and model of the furnace, how often is has been serviced and the environment it is in. What does a furnace service include? There are a lot of things that should be done while servicing a furnace, 1. Change the filter. 2. Clean the blower motor air vents. 3. Clean the burners if needed. 4. Adjust and calibrate the burners and gas control valve. 5. Visually inspect the heat exchanger for cracks or failure. 6. Preform a C.O. test to see if Carbon Monoxide is leaking. 7. Test the safeties to see that they are working. 8. Check the gas control valve and fittings to see if there are any gas leaks. 9. Check the electrical connections to make sure they are tight. 10. Check the amp draw on the blower motor. 11. Check the resistance on the igniter. 12. Clean and inspect the flame sensor. 13. Oil any points on the motor or draft inducer when required. 14. Inspect the flue piping to make sure it is safe. 15. Clean and inspect the draft inducer. 16. Inspect for any rust areas that may be a problem.

Yes you can do a basic service by changing the filter however it is strongly recommended that a professional should do a yearly service to make sure all things are operating safely.

Yes you can do a basic service by changing the filter however it is strongly recommended that a professional should do a yearly service to make sure all things are operating safely.

The average life expectancy should be about 12 years to 25 years. There are a lot of factors that have an effect on the life of a furnace, like the brand and model of the furnace, how often is has been serviced and the environment it is in.

A service and clean should take anywhere from about 30 minutes to 90 minutes.

Yes, by preforming a tune up the system will operate better with less break downs, the air will flow through the furnace making it more energy efficient, by calibrating the gas valve to the manufacturer’s specifications it will operate more efficiently. By servicing a furnace you should save from 5% to 15% of the operating costs and lengthen the life of the parts.

There are many factors involved that can determine the price. Here are some of the things that effect the price. Dealing with an existing AC system will add to the price, the efficiencies range from 82% to 98%, Different features such as a constant speed or variable speed blower, a 2 stage system, there are builders grade models to high quality models, access and location such as a tight closet or closet and if things are needed to bring up to code or make safe. All of these will affect the price to replace a furnace. Replacing a furnace can range from about $4,000 to over $16,000. Pricing is dependent a lot on the company you are working with and what features are important to you along with your budget. Financing is usually available that can help spread out the cost over time.

There are many reasons that can cause a furnace to stop working. You should check the thermostat to start, the batteries in some thermostats can go dead and need replacement. There are many other safeties in a furnace that will not let it turn on if something is not right or you may have a component that has failed. Anything outside of the batteries you should have a professional out to diagnose what is going on and give you options to repair it.

There are many reasons that can cause a furnace to stop working. You should check the thermostat to start, the batteries in some thermostats can go dead and need replacement. There are many other safeties in a furnace that will not let it turn on if something is not right or you may have a component that has failed. Anything outside of the batteries you should have a professional out to diagnose what is going on and give you options to repair it.

There are many factors involved that can determine the price. Here are some of the things that effect the price. Dealing with an existing AC system will add to the price, the efficiencies range from 82% to 98%, Different features such as a constant speed or variable speed blower, a 2 stage system, there are builders grade models to high quality models, access and location such as a tight closet or closet and if things are needed to bring up to code or make safe. All of these will affect the price to replace a furnace. Replacing a furnace can range from about $4,000 to over $16,000. Pricing is dependent a lot on the company you are working with and what features are important to you along with your budget. Financing is usually available that can help spread out the cost over time.

The average life expectancy should be about 12 years to 25 years. There are a lot of factors that have an effect on the life of a furnace, like the brand and model of the furnace, how often is has been serviced and the environment it is in.

There are many factors involved that can determine the price. Here are some of the things that effect the price. Dealing with an existing AC system will add to the price, the efficiencies range from 82% to 98%, Different features such as a constant speed or variable speed blower, a 2 stage system, there are builders grade models to high quality models, access and location such as a tight closet or closet and if things are needed to bring up to code or make safe. All of these will affect the price to replace a furnace. Replacing a furnace can range from about $4,000 to over $16,000. Pricing is dependent a lot on the company you are working with and what features are important to you along with your budget. Financing is usually available that can help spread out the cost over time.

The average life expectancy should be about 12 years to 25 years. There are a lot of factors that have an effect on the life of a furnace, like the brand and model of the furnace, how often is has been serviced, the environment it is in and how many problems you have had with it. When it is getting older it will also not be as energy efficient, anything over 15 years old is losing anywhere from 4% to over 10% of its efficiency. This in its self gives a good reason to consider replacing a furnace that is older than 15 years.

If your furnace and air conditioner HVAC system is older than 15 to 20 years and selling your home it can add the full cost of the new furnace back into the value of the home. A new system can be as much as 25% more efficient so even if you are not selling your home you will be saving a lot on your energy bills.

There are many things that go into pricing. Like how established the company is, how experienced are the technicians, the quality of the material or parts, the company’s reputation and reviews will say a lot about pricing, weather is not they are paid on commission or hourly, it is always best if the company has pricing in a company book or on software. Finding a good plumber is like finding a good dentist, you don’t want to use them any more than you need to but it is good to have a good company that you feel comfortable using. The average Plumbing Company in Denver is charging about $200 per hour at this time.

There are many expenses that go into building and supporting a good quality company. A lot of training goes into developing and training a good technician, the tools and material can be expensive, insurance and liability can be very expensive, required ongoing training by the State of Colorado, tools and equipment, vehicles, stocked material on the trucks and office, office equipment and supplies, employee benefits, needed office help and advertising. We have some of the best technicians in the business and their pricing is on the lower side of their competitors pricing.

Find one with some good reviews and make sure they belong to the Denver BBB and some of the other reputable referring companies Like Team Dave Logan, The Trouble Shooter, We are A+ Rated with the BBB and a leading member of all of the certified referral companies.

Find one with some good reviews and make sure they belong to the Denver BBB and some of the other reputable referring companies Like Team Dave Logan, The Trouble Shooter, Five Star rated. We Are A+ Rated with the BBB and a leading member of all of the certified referral companies.

The best way is to do your research on the company and read their reviews and complaints on the Denver BBB. Time Plumbing, Heating & Drains is A+ Rated with the BBB and a leading member of all of the certified referral companies. Time offers discounts for everything and gives additional discounts for military, first responders, teachers, seniors, Sam’s Club, Costco, and single parents.

The plumbing industry is short on qualified plumbers and many times they are short staffed. We have not lost any plumbers through covid and can still respond quickly to get customers taken care of.

Slow drains or backed up drains are the most common followed by leaks. The most common drain backups are from either grease or roots growing into the pipe. Be sure to use paper towels to wipe grease from pans before washing them out, you can use enzyme cleaners to help prevent grease from building up. If you have roots in the line these should be cleaned yearly to slow down or prevent major damage from occurring. The line should also be treated with a root killer.

For planned visits, it depends on the age of the house. Newer homes should be checked or inspected every 2 to 5 years. Homes older than 15 years should be checked or inspected every 1 to 2 years. For unplanned visits they should come whenever you have a plumbing issue to get it taken care of.

It is good to start by saying hello, than descried what is going on. See how helpful they are and if they can meet your needs. They should tell you what their initial charges are such as a trip charge or a diagnostic fee. If they don’t seem helpful or you don’t get a good impression of them there are many other plumbing companies that want your business?

Different lines have different challenges. A bathroom sink is much easier to clean than a kitchen line that is full of grease. The main line may have a crease a root problem or be broken or starting to collapse, everything you encounter needs a different approach to get it open. Many times people will get the cable stuck in the line or even break off in the line. Unless you are very mechanically inclined and have done some plumbing in the past I would recommend calling a plumber.

It depends. If it is a drain line, stop running all water. If there is a leak shut the water off to the fixture if you can. If there is not a shut off to the fixture shut off the main water valve to the house. Than call the plumber.

It depends, Drano works fairly well if the stoppage is in the P-Trap right at the fixture. Here are the problems with Drano. It is a caustic acid that can be very dangerous to your pipes and to you. It can dissolve or eat through thin metal and leak all over. This is not easy to clean up if this happens. If for some reason it does not work most get a big up-charge to clean the line with dangerous acid in it. This can be from an extra $70 to over $200 for them to clean a drain with Drano in it. This is because of the dangers to the technician and it shortens the life of the cleaning cable. Also the cable needs to be washed after cleaning. I would recommend calling a plumber.

It depends, Drano works fairly well if the stoppage is in the P-Trap right at the fixture. Here are the problems with Drano. It is a caustic acid that can be very dangerous to your pipes and to you. It can dissolve or eat through thin metal and leak all over. This is not easy to clean up if this happens. If for some reason it does not work most get a big up-charge to clean the line with dangerous acid in it. This can be from an extra $70 to over $200 for them to clean a drain with Drano in it. This is because of the dangers to the technician and it shortens the life of the cleaning cable. Also the cable needs to be washed after cleaning. I would recommend calling a plumber.

Using a plunger will not damage pipes, many times these new low flow toilets have a lot of stoppages and many times need 2 flushes to operate correctly. We have had the least amount of stoppages with the Toto and American Standard toilets.

It depends on the type of stoppage, what size of line and what kind of access to the drain. Sometimes a plunger is used, an auger is used for stoppages in the toilet trap, there are small cables for bathtubs, there are medium sized cables for cleaning sink lines or secondary lines up to 2” lines and for main sewer drains there is large cable that is used. There are also sewer jetters that use high pressure water for cutting through and flushing grease out of the line. There are also chain cleaners for cleaning scale out of the line. A professional will know what is the best solution for your drain problem and should make recommendations.

Find one with some good reviews and make sure they belong to the Denver BBB and some of the other reputable referring companies Like Team Dave Logan, The Trouble Shooter, Five Star rated. We Are A+ Rated with the BBB and a leading member of all of the certified referral companies.

Find one with some good reviews and make sure they belong to the Denver BBB and some of the other reputable referring companies Like Team Dave Logan, The Trouble Shooter, Five Star rated. We Are A+ Rated with the BBB and a leading member of all of the certified referral companies.

This is a tough one to answer. Many plumbers that are on commission will only give you the most expensive solution because they make more money. Find one with some good reviews and make sure they belong to the Denver BBB and some of the other reputable referring companies Like Team Dave Logan, The Trouble Shooter, Five Star rated. We Are A+ Rated with the BBB and a leading member of all of the certified referral companies. Even with good companies you still need to use your best judgment on making your decision. Trust will come over time and until that time always be a little cautious.

This is a tough one to answer. Many plumbers that are on commission will only give you the most expensive solution because they make more money. Find one with some good reviews and make sure they belong to the Denver BBB and some of the other reputable referring companies Like Team Dave Logan, The Trouble Shooter, Five Star rated. We Are A+ Rated with the BBB and a leading member of all of the certified referral companies. Even with good companies you still need to use your best judgment on making your decision. Trust will come over time and until that time always be a little cautious.

This is a tough one to answer. Many plumbers that are on commission will only give you the most expensive solution because they make more money. Find one with some good reviews and make sure they belong to the Denver BBB and some of the other reputable referring companies Like Team Dave Logan, The Trouble Shooter, Five Star rated. We Are A+ Rated with the BBB and a leading member of all of the certified referral companies. Even with good companies you still need to use your best judgment on making your decision. Trust will come over time and until that time always be a little cautious.

Slow drains or backed up drains are the most common followed by leaks. The most common drain backups are from either grease or roots growing into the pipe. Be sure to use paper towels to wipe grease from pans before washing them out, you can use enzyme cleaners to help prevent grease from building up. If you have roots in the line these should be cleaned yearly to slow down or prevent major damage from occurring. The line should also be treated with a root killer.

Well this depends on a lot of things. How mechanically inclined you are, if you worked on plumbing before, if you have the right tools for the job, sometimes finding the correct repair parts can be challenging. Just remember you are working with pressurized water and if something goes wrong there can be a lot of damage. We are out almost weekly to correct homeowner’s repairs and many times there is water damage that has occurred.

Plumbers make anywhere from about $30,000 to over $200,000

It depends on different things hourly plumbers make between $20 and $80 per hour, however a plumber at $30 per hour can make more than someone at $60 per hour. It depends on how many hours per week they are working. Many companies will pay either by commissions or piece work, this gives the technician to make more money by what he sells. Service plumbers can make the most money although new construction piece work plumbers can make some good money also.

There are a lot of variables involved. The cost to clear a drain ranges from about $69 to about $140 with the average cost being about $95. When you get a drain cleaned there is a lot more time involved than clearing a drain. Cleaning a drain removes all of the roots grease or debris that is in the line. This is done by using a drain machine using multiple blades and degreasers when needed. Sometimes it is necessary to clean the line using a high pressure jetter to break up the grease and wash it out. Cleaning a drain or sewer line can cost from $250 to as much as $1800 with the average cost to clean a line being about $425

It depends, Drano works fairly well if the stoppage is in the P-Trap right at the fixture. Here are the problems with Drano. It is a caustic acid that can be very dangerous to your pipes and to you. It can dissolve or eat through thin metal and leak all over. This is not easy to clean up if this happens. If for some reason it does not work most plumbers get a big up-charge to clean the line with dangerous acid in it. This can be from an extra $70 to over $200 for them to clean a drain with Drano in it. This is because of the dangers to the technician and it shortens the life of the cleaning cable. Also the cable needs to be washed after cleaning. I would recommend calling a plumber in most cases.

It depends on the type of stoppage, what size of line and what kind of access to the drain. Sometimes a plunger is used, an auger is used for stoppages in the toilet trap, there are small cables for bathtubs, there are medium sized cables for cleaning sink lines or secondary lines up to 2” lines and for main sewer drains there is large cable that is used. There are also sewer jetters that use high pressure water for cutting through and flushing grease out of the line. There are also chain cleaners for cleaning scale out of the line. A professional will know what is the best solution to resolve your drain problem and should make recommendations. And what about Drano? Drano works fairly well if the stoppage is in the P-Trap right at the fixture. Here are the problems with Drano. It is a caustic acid that can be very dangerous to your pipes and to you. It can dissolve or eat through thin metal and leak all over. This is not easy to clean up if this happens. If for some reason it does not work most plumbers get a big up-charge to clean the line with dangerous acid in it. This can be from an extra $70 to over $200 for them to clean a drain with Drano in it. This is because of the dangers to the technician and it shortens the life of the cleaning cable. Also the cable needs to be washed after cleaning. I would recommend calling a plumber in most cases.

It depends on the type of stoppage, what size of line and what kind of access to the drain. Sometimes a plunger is used, an auger is used for stoppages in the toilet trap, there are small cables for bathtubs, there are medium sized cables for cleaning sink lines or secondary lines up to 2” lines and for main sewer drains there is large cable that is used. There are also sewer jetters that use high pressure water for cutting through and flushing grease out of the line. There are also chain cleaners for cleaning scale out of the line. A professional will know what is the best solution to resolve your drain problem and should make recommendations.

Drano works fairly well if the stoppage is in the P-Trap right at the fixture. Here are the problems with Drano. It is a caustic acid that can be very dangerous to your pipes and to you. It can dissolve or eat through thin metal and leak all over. This is not easy to clean up if this happens. If for some reason it does not work most plumbers get a big up-charge to clean the line with dangerous acid in it. This can be from an extra $70 to over $200 for them to clean a drain with Drano in it. This is because of the dangers to the technician and it shortens the life of the cleaning cable. Also the cable needs to be washed after cleaning. I would recommend calling a plumber in most cases.

Drano works fairly well if the stoppage is in the P-Trap right at the fixture. Here are the problems with Drano. It is a caustic acid that can be very dangerous to your pipes and to you. It can dissolve or eat through thin metal and leak all over. This is not easy to clean up if this happens. If for some reason it does not work most plumbers get a big up-charge to clean the line with dangerous acid in it. This can be from an extra $70 to over $200 for them to clean a drain with Drano in it. This is because of the dangers to the technician and it shortens the life of the cleaning cable. Also the cable needs to be washed after cleaning. I would recommend calling a plumber in most cases.

The 2 strongest are muriatic and sulfuric acid. These are extremely strong and dangerous to use and not recommended for use other than professionals, even than professionals will rarely use these and cable cleaning is better for the environment and safer to use. Drano works fairly well if the stoppage is in the P-Trap right at the fixture. Here are the problems with Drano. It is a caustic acid that can be very dangerous to your pipes and to you. It can dissolve or eat through thin metal and leak all over. This is not easy to clean up if this happens. If for some reason it does not work most plumbers get a big up-charge to clean the line with dangerous acid in it. This can be from an extra $70 to over $200 for them to clean a drain with Drano in it. This is because of the dangers to the technician and it shortens the life of the cleaning cable. Also the cable needs to be washed after cleaning. I would recommend calling a plumber in most cases.

Once Drano is in a line it is a very dangerous acid that will dissolve skin. When plunging a lot of water and in this case Drano can splash out and get on your skin or in your eyes. Drano works fairly well if the stoppage is in the P-Trap right at the fixture. Here are the problems with Drano. It is a caustic acid that can be very dangerous to your pipes and to you. It can dissolve or eat through thin metal and leak all over. This is not easy to clean up if this happens. If for some reason it does not work most plumbers get a big up-charge to clean the line with dangerous acid in it. This can be from an extra $70 to over $200 for them to clean a drain with Drano in it. This is because of the dangers to the technician and it shortens the life of the cleaning cable. Also the cable needs to be washed after cleaning. I would recommend calling a plumber in most cases.

You can but now you are raising the risk of the dangers of using draino, now you could also get burnt from the boiling water. Drano works fairly well if the stoppage is in the P-Trap right at the fixture. Here are the problems with Drano. It is a caustic acid that can be very dangerous to your pipes and to you. It can dissolve or eat through thin metal and leak all over. This is not easy to clean up if this happens. If for some reason it does not work most plumbers get a big up-charge to clean the line with dangerous acid in it. This can be from an extra $70 to over $200 for them to clean a drain with Drano in it. This is because of the dangers to the technician and it shortens the life of the cleaning cable. Also the cable needs to be washed after cleaning. I would recommend calling a plumber in most cases.

It is highly unlikely that dawn will unclog a drain. It will not harm anything in trying it as it does break down grease. Even if it did work it would only open a very small path and it would most likely stop up again in a short period of time. I would recommend calling a plumber in most cases.

I would not recommend leaving it in the line overnight if your home is older than 40 years or if you have metal drain pipes. Drano works fairly well if the stoppage is in the P-Trap right at the fixture. Here are the problems with Drano. It is a caustic acid that can be very dangerous to your pipes and to you. It can dissolve or eat through thin metal and leak all over. This is not easy to clean up if this happens. If for some reason it does not work most plumbers get a big up-charge to clean the line with dangerous acid in it. This can be from an extra $70 to over $200 for them to clean a drain with Drano in it. This is because of the dangers to the technician and it shortens the life of the cleaning cable. Also the cable needs to be washed after cleaning I would recommend calling a plumber in most cases.

Yes this can happen in some cases where the drain is very slowly draining and the plumber tries to open the line. If they are unable to get his cable through the blockage due to a damaged or collapsed line it can completely stop up the line. This is a rear occurrence but it can happen. If there is that big of a problem this will help expose it so it can be fixed. Most plumbers can locate exactly where the problem is using locating equipment and give you pricing to repair it if needed.

Once Drano is in a line it is a very dangerous acid that will dissolve skin. When plunging a lot of water and in this case Drano can splash out and get on your skin or in your eyes. Drano works fairly well if the stoppage is in the P-Trap right at the fixture. Here are the problems with Drano. It is a caustic acid that can be very dangerous to your pipes and to you. It can dissolve or eat through thin metal and leak all over. This is not easy to clean up if this happens. If for some reason it does not work most plumbers get a big up-charge to clean the line with dangerous acid in it. This can be from an extra $70 to over $200 for them to clean a drain with Drano in it. This is because of the dangers to the technician and it shortens the life of the cleaning cable. Also the cable needs to be washed after cleaning. I would recommend calling a plumber in most cases.

Drano works fairly well if the stoppage is in the P-Trap right at the fixture. Here are the problems with Drano. It is a caustic acid that can be very dangerous to your pipes and to you. It can dissolve or eat through thin metal and leak all over. This is not easy to clean up if this happens. If for some reason it does not work most plumbers get a big up-charge to clean the line with dangerous acid in it. This can be from an extra $70 to over $200 for them to clean a drain with Drano in it. This is because of the dangers to the technician and it shortens the life of the cleaning cable. Also the cable needs to be washed after cleaning. I would recommend calling a plumber in most cases.

There are a lot of variables involved. The cost to clear a drain ranges from about $69 to about $140 with the average cost being about $95. When you get a drain cleaned there is a lot more time involved than clearing a drain. Cleaning a drain removes all of the roots grease or debris that is in the line. This is done by using a drain machine using multiple blades and degreasers when needed. Sometimes it is necessary to clean the line using a high pressure jetter to break up the grease and wash it out. Cleaning a drain or sewer line can cost from $250 to as much as $1800 with the average cost to clean a line being about $425

There are a lot of variables involved. The cost to clear a drain ranges from about $69 to about $140 with the average cost being about $95. When you get a drain cleaned there is a lot more time involved than clearing a drain. Cleaning a drain removes all of the roots grease or debris that is in the line. This is done by using a drain machine using multiple blades and degreasers when needed. Sometimes it is necessary to clean the line using a high pressure jetter to break up the grease and wash it out. Cleaning a drain or sewer line can cost from $250 to as much as $1800 with the average cost to clean a line being about $425

Different lines have different challenges. A bathroom sink is much easier to clean than a kitchen line that is full of grease. The main line may have a crease a root problem or be broken or starting to collapse, everything you encounter needs a different approach to get it open. Many times people will get the cable stuck in the line or even break off in the line. Unless you are very mechanically inclined and have done some plumbing in the past I would recommend calling a plumber.

Different lines have different challenges. A bathroom sink is much easier to clean than a kitchen line that is full of grease. The main line may have a crease a root problem or be broken or starting to collapse, everything you encounter needs a different approach to get it open. The average time to set up and clean a drain is usually 1 to 2 hours.

Different lines have different challenges. A bathroom sink is much easier to clean than a kitchen line that is full of grease. The main line may have a crease a root problem or be broken or starting to collapse, everything you encounter needs a different approach to get it open. Most commonly drains are cleared using a machine with a cable.

It is by far better and much safer for the user and environment to use a drain machine. Drano works fairly well if the stoppage is in the P-Trap right at the fixture. Here are the problems with Drano. It is a caustic acid that can be very dangerous to your pipes and to you. It can dissolve or eat through thin metal and leak all over. This is not easy to clean up if this happens. If for some reason it does not work most plumbers get a big up-charge to clean the line with dangerous acid in it. This can be from an extra $70 to over $200 for them to clean a drain with Drano in it. This is because of the dangers to the technician and it shortens the life of the cleaning cable. Also the cable needs to be washed after cleaning. I would recommend calling a plumber in most cases.

Well it is already stopped up and plunging it will either open it up and start draining or it will still be stopped up. It will not damage anything unless there is a thin rusted through pipe that is already having a problem.

The 2 strongest are muriatic and sulfuric acid. These are extremely strong and dangerous to use and not recommended for use other than professionals, even than professionals will rarely use these and cable cleaning is better for the environment and safer to use. Drano works fairly well if the stoppage is in the P-Trap right at the fixture. Here are the problems with Drano. It is a caustic acid that can be very dangerous to your pipes and to you. It can dissolve or eat through thin metal and leak all over. This is not easy to clean up if this happens. If for some reason it does not work most plumbers get a big up-charge to clean the line with dangerous acid in it. This can be from an extra $70 to over $200 for them to clean a drain with Drano in it. This is because of the dangers to the technician and it shortens the life of the cleaning cable. Also the cable needs to be washed after cleaning. I would recommend calling a plumber in most cases.